5/6/2024 0 Comments Change vlc streamer IP address![]() You may have to contact support for your specific model. Note: Swann uses various lines of hardware and software and RTSP streams. Swann camera RTSP where 0 = mainstream and 1 = substream Samsung / Hanwha Techwin Camera RTSP - stream type either 1 for mainstream or 2 for substreamĮxample URL: will bring up mainstream for a camera on 192.168.1.210 c1 would be channel 1, c2 channel 2, etcĮxample URL: will bring up substream for channel 2.Įxample URL rtsp://192.168.1.210/axis-media/media.ampĪvigilon RTSP RTSP streams must be generated in the web UI of the camera under compression and image rate. You can also encode credentials into the URL by entering it prior to the IP address - for example.Įxample URL: will bring up mainstream for channel 1, where admin is the username and 12345 is the password. This RTSP stream would mainstream channel 1 on an NVR at 192.168.1.210. 201 would produce the channel #2 of the NVR and mainstream and 202 would produce channel #2 and substream.Įxample: rtsp://192.168.1.210:554/Streaming/Channels/101 Changing the to 102 would create channel 1 and stream #2. streaming channel - for example “101” would be channel 1 and stream #1 (mainstream). The of main stream is 0, extra stream 1 is 1, extra stream 2 is 2.Įxample URL: will bring up substream for channel 1 ![]() Some Common RTSP URLS: Dahua RTSP stream (Cameras & - the IP address of the IP Camera. This will indicate if the camera is having a bandwidth issue and is dropping packets. When we are testing for packet loss you will select "Tools" and then "Codec Information". If all is successful it will display the RTSP stream. Enter the Camera specific RTSP stream.Īfter entering in the URL and pressing Play you should be prompted to put in the cameras Username and Password. You must test it with VLC because the way the software pulls the stream in is through RTSP on port 554.ģ. ![]() Navigating to the cameras web interface does not mean that the camera will work. If a camera cannot connect using VLC it will give us a better idea of what is going on with the camera. This is to test the RTSP stream and make sure it is connecting. You will have to test the camera using VLC media player. ![]() You will need to note the password you use and provide it to the user at your destination.You may run into issues with a camera connecting or after setting up a camera you may see a red X. The password used by both the source and destination to encrypt the stream. If you are using SRT on a network protected with a router and firewall, you may need to configure the router to support port forwarding for whatever port you specify. The port used between the destination and source SRT device. The IP address of the destination SRT device. If the destination device is going to be ingesting multiple SRT sources, then it must be configured as a listener and Media Composer must be configured as a caller. The device you set as the caller or listener is arbitrary in most cases. To establish a link between a source and destination device, ensure that one device is a listener and the other is a caller. You can provide a custom name for the stream You might find the information in the Media Composer Editing Guide helpful: Start the Broadcaster via the HW/SW button on the timeline window, press play on the iPad QuickPlay page down the bottom. Check that the Port numbers are the same on the AVID and PlayerPro. As the AVID defaults to the "caller" mode, try selecting the "Listener" mode on the PlayerPro Quickplay page. You just need to get the IP address of the iPad which can be found via the Player Pro app on the QuickPlay page - just select the "Play an SRT Stream" from the opening page of Haivision app, get the IP address sent to you and enter that in the AVID selection. (If multiple people want to view at the same time them I think this requires the Haivision Gateway at an addtional cost) One iPad via the Haivision Player Pro App should work.
0 Comments
Leave a Reply. |